Click Here!

 

 

Just about everyone has their own individual way of thinking involving How to Install a Bathtub.

Installing a tub isn't exactly rocket science, however it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is also a moderately tough task. If the old tub is conveniently accessible, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bathtub, the task is much harder. In either situation, the task is within a residence handyman's abilities, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. See to it you have qualified on your own for the work and are comfortable trying it. As opposed to hiring a specialist to take control of a halfway-completed task, it is better to think about utilizing one prior to you start. Chances are you may need an expert plumber to make tube links.
This write-up will help you set up a new tub in your washroom if you have actually currently bought a new bathtub and also do not need to change the arrangement of your previous supply of water pipes.
Your devices as well as product list need to consist of the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Removing Old Taps

If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of getting rid of the existing faucets can be rather troublesome due to the restricted accessibility that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
Before going on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.

 

 

Suitable New Taps

If the tails of the new faucets are plastic, after that you will require a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in place in between the tap and the sink. Safeguard the tap in position with the producer provided backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Mounting the Bathtub

Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are handy in evenly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the tub till the level reads degree.
To mount taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water system and also check all joints and new pipework for leaks as well as tighten them if essential. Fill the bathtub as well as also inspect the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, fix the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the bathtub ought to wait up until the bath tub has actually been used a minimum of when as this will certainly resolve it right into its final position.

 

 

Getting ready for the Setup

Firstly, the sustaining structure provided with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be fitted in its last placement.

 

 

Tiling Around the Tub

In the area where the bath fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to fracture a stiff seal, causing the water to penetrate the wall surface in between the bath and also the tiling, causing issues with dampness and also feasible leaks to the ceiling listed below.
You can select from a range of coloured sealers to blend in your components as well as installations. They are offered in tubes and also cartridges, as well as are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water before sealing, to permit the motion experienced when the bathtub is in usage. The sealant can split fairly early if you do not take into consideration this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly available on the marketplace. It is advisable to fit the floor tiles using waterproof or waterproof sticky and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you enjoyed our piece on A Step-by-Step Guide to Installing a Bathtub. Thanks for taking time to read our post. Loved our post? Please share it. Let another person discover it. Thank you for your time. Visit again soon.

Click On This Link